Running Out of Power on 100 Amp Service?
Many homes around here still run on the 100 amp service they were built with in the 1950s. That was plenty for a fridge and a few lamps. It struggles once you add central AC, an electric dryer and a microwave, and it often runs out of room when an EV joins the family.
You feel it in small ways first. The AC breaker trips on hot afternoons, the lights dim when the dryer starts, and there is no free slot for a new circuit. Some owners only find out when a charger permit gets flagged because the existing service is too small for the added load.
Homes That Need a 200 Amp Upgrade
Not every home needs 200 amps, but some situations almost always call for it. These are the owners we upgrade most often.
EV Owners and All Electric Remodels
A Level 2 EV charger, an induction range and a heat pump water heater can each add a big load. Put two or three together on 100 amps and the panel runs out of room fast. A 200 amp upgrade for EV charger plans keeps everything running at once.
Families With Two AC Units or a Heat Pump
Two story homes and larger remodels often run two systems in summer. Add a heat pump in place of a gas furnace and the load climbs again. Bigger service lets cooling, cooking and laundry run on the same afternoon without trips.
ADU Builders and Landlords
An ADU, a hot tub or a rental modernization adds circuits the old panel cannot hold. Landlords in Oakdale and Larchmont Village often upgrade between tenants, so the rental is ready for modern appliances and passes inspection with a clean record.
Load Calculation First, So You Only Upgrade When Needed
A bigger panel is not always the answer. Before we quote any upgrade, we run a load calculation that adds up every appliance and system in your home. If your current service can handle your plans, we tell you so.
When a Load Device Is the Better Choice
Some homes can add a car charger without new service by using a load management device that pauses charging when the dryer or AC runs. SMUD rebates these devices up to $200. We compare both options so you only pay for the one that fits.
| Your Situation | Likely Best Fit |
|---|---|
| One EV and gas appliances | Load device on current service |
| EV plus heat pump | 200 amp upgrade |
| Full electric remodel | 200 amp upgrade |
| Hot tub or ADU added | 200 amp upgrade or subpanel |
| No new loads, old panel | Same size panel swap |
SMUD Meter Base Changes and Reconnect Handled
Moving to 200 amps often means the meter base and service entrance conductors must change too. That brings the utility into the job. Instead of leaving you to manage SMUD (Sacramento Municipal Utility District) on your own, we coordinate every step with them.
- We check the meter base first: A rusted or undersized base cannot carry 200 amps safely. We flag it during the quote, so the price already includes it if a new base is needed.
- We request the disconnect: The utility must pull the meter before we can swap the service. We schedule that ahead of swap day so your crew is not left waiting.
- We handle the reconnect timing: After the county approves the work, SMUD typically energizes new service within about 7 business days. We book the inspection fast to keep that window short.
- We explain utility fees upfront: SMUD lists a $134 truck reconnect fee in its fee schedule. We tell you about fees like this before work starts, so nothing on the final bill feels like a surprise.
200 Amp Upgrades Set Up for the SMUD Go Electric Rebate
A SMUD 200 amp upgrade rebate can take a real chunk off the cost. The Go Electric bonus pays up to $2,000 when your panel upgrade adds future circuits for an EV, a range and a dryer and the home is ready for all electric use. We build the job around those rules from the start.
What We Do So Your Upgrade Can Qualify
- Confirm the new panel stays at 200 amps or less
- Add a future EV charger circuit during the upgrade
- Add a 240 volt range or cooktop circuit
- Add an electric dryer circuit
- Write the invoice the way the utility asks
- Check current program rules before every job
- Give you copies of everything for your claim
Recent 100 to 200 Amp Upgrades in North Highlands
Recent jobs include a 100 to 200 amp upgrade on a ranch home off Hillsdale Boulevard and a meter base change near Madison Avenue so a family could add a heat pump and charger.


Panels and Breakers Used in Our 200 Amp Upgrades
Every 200 amp breaker panel North Highlands homes get from us comes from a trusted maker like Square D, Eaton or Siemens. We match the brand to what fits your wall and what parts are easy to find later, so future repairs stay simple.
Inside the panel, we install AFCI and GFCI breakers where the code calls for them and label every circuit by room. We also check the grounding electrode and bonding, because a new panel only works as well as its ground. A whole house surge protector is an easy add on while the panel is open.
200 Amp Upgrade Cost and Rebate Savings
Most 200 amp jobs in the Sacramento area cost between $2,500 and $8,000. The biggest factor is whether the meter base and service entrance can stay. Use these ranges to understand your 200 amp service upgrade cost before we visit.
| Job | Typical Area Range |
|---|---|
| Panel only upgrade | $2,500 to $4,500 |
| Panel plus new meter base | $3,500 to $6,000 |
| New service entrance | $4,500 to $8,000 |
Ranges from SacValley Contractors 2026.
A Go Electric rebate of up to $2,000 can lower the total on qualifying jobs. Your actual 200 amp panel price North Highlands quote depends on panel location, wall access and meter needs. Whether you need a 200 amp panel installation 95660 job or a 200 amp main panel replacement 95842 address, you get the full number in writing first.
Ready to Stop the Breaker Trips?
Living with a panel that trips every summer gets old fast. You plan laundry around the AC, unplug the microwave before running the toaster and wonder if a new car charger will even work. A properly sized panel ends that guessing game for good.
It also adds value. A permitted 200 amp upgrade is a plus for buyers, insurers and appraisers, and it leaves room for whatever your home needs next, from a hot tub to an ADU in the backyard.
200 Amp Upgrade Answers for North Highlands Homes
Here are quick answers to what owners ask before booking a 200 amp upgrade contractor near me.
Panel only upgrades often run $2,500 to $4,500. If the utility needs a new meter base or service wires, plan on $3,500 to $8,000. Go Electric can take up to $2,000 off qualifying jobs.
Not always. A load calculation tells us. Many homes fit a 32 amp charger on existing service with a load management device. If the math says you need more, we quote both options side by side.
Yes. Every 200 amp upgrade with permit North Highlands jobs includes the county filing, the inspection booking and an electrician on site to meet the inspector. The permit fee is part of your written price.
Yes. A 200 amp panel upgrade Foothill Farms owners book gets the same crew and the same county permit process. Anyone looking to upgrade to 200 amp service Sacramento County side can call us.
Areas We Serve


